Electric Power Plant



Electric power plant

Electricity is produced at a an electric power plant. Some fuel source, such as coal, oil, natural gas, or nuclear energy produces heat. The heat is used to boil water to create steam. The steam under high pressure is used to spin a turbine. The spinning turbine interacts with a system of magnets to produce electricity. The electricity is transmitted as moving electrons through a series of wires to homes and business.

Electric Power Plants have a number of components in common and are an interesting study in the various forms and changes of energy necessary to produce electricity.

 

Boiler Unit: Almost all of power plants operate by heating water in a boiler unit into super heated steam at very high pressures. The source of heat from combustion reactions may vary in fossil fuel plants from the source of fuels such as coal, oil, or natural gas. Biomass or waste plant parts may also be used as a source of fuel. In some areas solid waste incinerators are also used as a source of heat. All of these sources of fuels result in varying amounts of air pollution, as well as, the carbon dioxide ( a gas implicated in global warming problems).

In a nuclear power plant, the fission chain reaction of splitting nuclei provides the source of heat.

Turbine-Generator: The super heated steam is used to spin the blades of a turbine, which in turn is used in the generator to turn a coil of wires within a circular arrangements of magnets. The rotating coil of wire in the magnets results in the generation of electricity.

Cooling Water: After the steam travels through the turbine, it must be cooled and condensed back into liquid water to start the cycle over again. Cooling water can be obtained from a nearby river or lake. The water is returned to the body of water 10 -20 degrees higher in temperature than the intake water. Alternate method is to use a very tall cooling tower, where the evaporation of water falling through the tower provides the cooling effect.

Domestic power supply and safety for handling electricity

Precautions to be taken while working with electricity  

  • Check for damage on power plugs, wire and other electrical fittings. If found damaged, repair or replace damaged equipment immediately.  
  • Keep electrical wires of equipment away from hot surfaces to prevent damage of the insulation.  
  • Do not lay electric wires along passage. It can be a trip hazard. Further contact with sharp edges can cause damage to insulation leading to short circuit.  
  • Know the location of switches/circuit breaker boxes for use in case of an emergency.
  • All circuit breakers in the switch board must be clearly labelled for easy identification.
  • Access to circuit breakers must not be blocked.
  • Extension cords must be used only to supply power temporarily.
  • Do not handle electrical equipment when hands, feet or body are wet or perspiring, or when standing on a wet floor.
  • Consider all floors as conductive unless covered with insulating matting of suitable type for electrical work.
  • Whenever possible, use only one hand when working on circuits or control devices.
  • Do not wear rings, metallic watchbands, chains etc. when working with electrical equipment.

Precautions to be taken while using power tools

  • Before connecting the tool to the power supply, switch the tool OFF.
  • Disconnect power supply before making adjustments.
  • The tool must be properly grounded with a 3-wire cord with a 3-prong plug. Use double insulated tools wherever possible.
  • Do not use electrical tools in wet conditions or damp locations unless the tool is connected to an Earth Leakage Circuit Breaker.

Power distribution

Primary distribution lines contain a distribution transformer present in the locality of the clientele. Primary distribution ranges from 4 to 35-kilo Voltage. Only industries can directly feed the transmission line. Most average consumers are connected to a transformer that brings down the voltage to a useable level. The distribution network for the primary distribution comes in three types, although they are mainly of two types—radial or network. A radial network is primarily like a tree, where there is only one line of connection for the customer to the source of supply. A network system, on the other hand, has multiple or parallel connections to the source of supply. A radial connection is primarily used in rural areas, while the network connection is primarily used in load-sensitive areas, such as a dense urban area. However, as bad as radial systems sound, based on there only being a single connection to the source, modern-day radial networks do contain backup options.

The parameters that encompass the properties of electricity are not strictly limited to voltage and current. When it comes to electricity, there is a third important property of electricity—frequency. There are primarily two frequencies in which electricity is produced, either 50 or 60 Hz.  This electricity is then delivered to domestic customers as single-phase electric power.The domestic power supply in North America would look like a sine wave, oscillating between −170 volts and +170 volts, giving an effective voltage of 120 volts RMS.

However, in some countries of Europe and India, three-phase power is more efficient in terms of power delivered per cable used and is more suited to running large electric motors. Some large European appliances may be powered by three-phase power, such as electric stoves and clothes dryers. A ground connection is normally provided for the customer’s system, as well as for the equipment owned by the utility. The purpose of connecting the customer’s system to the ground is to limit the voltage that may develop if high voltage conductors fall onto lower-voltage conductors, which are usually mounted lower to the ground, or if a failure occurs within a distribution transformer; this process is also famously known as grounding.

National Grid

The Indian Power system for planning and operational purposes is divided into five regional grids. The integration of regional grids, and thereby establishment of National Grid, was conceptualised in early nineties. The integration of regional grids which began with asynchronous HVDC back-to-back inter-regional links facilitating limited exchange of regulated power was subsequently graduated to high capacity synchronous links between the regions.

The initial inter-regional links were planned for exchange of operational surpluses amongst the regions. However, later on when the planning philosophy had graduated from Regional self-sufficiency to National basis, the Inter-regional links were planned associated with the generation projects that had beneficiaries across the regional boundaries.

By the end of 12th plan the country has total inter-regional transmission capacity of about 75,050 MW which is expected to be enhanced to about 1,18,050 MW at the end of XIII plan.

Synchronisation of all regional grids will help in optimal utilization of scarce natural resources by transfer of Power from Resource centric regions to Load centric regions. Further, this shall pave way for establishment of vibrant Electricity market facilitating trading of power across regions. One Nation One Grid shall synchronously connect all the regional grids and there will be one national frequency.


Evolution of National Grid

  • Grid management on regional basis started in sixties.
  • Initially, State grids were inter-connected to form regional grid and India was demarcated into 5 regions namely Northern, Eastern, Western, North Eastern and Southern region.
  • In October 1991 North Eastern and Eastern grids were connected.
  • In March 2003 WR and ER-NER were interconnected .
  • August 2006 North and East grids were interconnected thereby 4 regional grids Northern, Eastern, Western and North Eastern grids are synchronously connected forming central grid operating at one frequency.
  • On 31st December 2013, Southern Region was connected to Central Grid in Synchronous mode with the commissioning of 765kV Raichur-Solapur Transmission line thereby achieving ‘ONE NATION’-‘ONE GRID’-‘ONE FREQUENCY’.

 


Exit mobile version